Repair and service Mercedes Benz M - The Class W163 - Removal and installation of back stupichny assembly, replacement of a spherical support//since 1997 release /

Mercedes M-Class W163

since 1997 release

Repair and operation of the car



Mercedes W163
+ Mercedes-Benz cars of a class M (W163)
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
+ A power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
- Transmission line
   + Coupling
   + Driveshafts
   - Power shafts
      Removal and installation of a rotary fist, replacement of a spherical support
      Removal and installation of a flange of a forward power shaft and two-row radial-stop ball bearing of a forward nave
      Removal and installation of back stupichny assembly, replacement of a spherical support
      Removal and installation of a flange of a back power shaft and two-row radial-stop ball bearing of a back nave
      Removal and installation of power shafts
      Replacement of boots of hinged assemblies of power shafts
   + Transfer case and differentials
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of back stupichny assembly, replacement of a spherical support

Removal/installation of stupichny assembly

Details of installation of back stupichny assembly

7 — Stupichnaya assembly
7a — the Lower spherical support
12 — Stupichnaya a nut
37 — the Power shaft
91a — the Top spherical support

97a — the extension Hinge
111 — the Brake support
112a — the Cable of the drive of the parking brake
112b — the Brake disk
L6/3 — the Left back wheel sensor


 PERFORMANCE ORDER

  1. Details of installation of back stupichny assembly are shown on an illustration to which all references which are found in the text belong.
  2. Cock the parking brake and give a stupichny nut (12).
  3. Remove the corresponding back wheel.
  4. Remove the wheel sensor (L6/3 in case of the left wheel).
  5. Remove a brake support (111) (see the Head Tormoznaya and auxiliary systems).
  6. Remove heat a disk (112b) (see the Head Tormoznaya and auxiliary systems).
  7. Take off boots of the parking brake (see the Head Tormoznaya and auxiliary systems).
  8. Release from a basic arm on stupichny assembly a cable of the drive of the parking brake (112a).
  9. By means of a stripper release from stupichny assembly the extension hinge (97a).
  10. Vypressuyte from stupichny assembly a spherical support (91a) the top lever of a suspension bracket.
  11. By means of an extractor to a vypressuyta from the flange a back power shaft, - try not to damage a boot of the CV JOINT and a rotor of the wheel sensor. Tie up the released shaft to suspension bracket/frame elements.
  12. Having recorded stupichny assembly, release a shaft of the lower spherical support (7a) from the cross lever of a suspension bracket.
  13. Remove stupichny assembly.
  14. Installation is made upside-down, in conclusion make necessary adjustments of angles of installation of wheels.

Replacement of a spherical support

Details of installation of the lower spherical support in a rotary fist


 PERFORMANCE ORDER

  1. Details of installation of the lower spherical support are shown on an illustration to which all references which are found in the text belong.
  2. Remove stupichny assembly (see above) and a vypressuyta the lower spherical support (7a) by means of a suitable mandrel (and).
  3. By means of a special key (9) give a koronchaty nut (7b).
  4. By means of a koronchaty nut and a special key press a new spherical support against the stop in stupichny assembly, - replace a nut.
  5. Establish stupichny assembly on the regular place.