Mercedes M-Class W163

since 1997 release

Repair and operation of the car



Mercedes W163
+ Mercedes-Benz cars of a class M (W163)
+ Governing bodies and methods of safe operation
+ Current leaving and service
+ Engine
+ Cooling systems, heating and air conditioner
- Power supply system and production of the fulfilled gases
   + Power supply system of petrol engines
   + Power supply system of diesel engines
   - Systems of release and decrease in toxicity of the fulfilled gases
      Removal and installation of system of production of the fulfilled gases
      Replacement of forward sections of system of production of the fulfilled gases on petrol models
      Removal and installation of catalytic converters on diesel models
      Removal and installation lambda probes
      Removal and installation of the EGR valve, - M112/113
      Removal and installation of a cooler of EGR, - diesel models
      Removal and installation of the air pump, - M112/113
      Removal and installation of a coal adsorber, - petrol models
      Removal and installation of the broad tank of accumulation of fuel evaporations, - appropriately completed model 163.113/154/128
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
+ Automatic transmission
+ Transmission line
+ Brake and auxiliary systems
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



Removal and installation of a cooler of EGR, - diesel models

M612

Details of installation of a cooler of EGR on models 163.113 (the series 612 engine)

1 — EGR Cooler
2 — a connection Branch pipe to a path of the cooling system

3 — Bolts
4 — the Basic arm


 PERFORMANCE ORDER

  1. Details of installation of a cooler of EGR on models 163.113 (the series 612 engine) are shown on an illustration to which all references which are found in the text belong.
  2. Empty the cooling system (see the Head of the Power supply system and production of the fulfilled gases).
  3. Remove panels of finishing of a cover of a head of cylinders.
  4. Turn out fixing screws (3) and remove a basic arm (4) with a branch pipe of connection to a path of the cooling system (2).
  5. Turn out the remained fixing bolts (3), remove assembly of a cooler of EGR (1) from a head of cylinders and separate it from system of production of the fulfilled gases.
  6. Installation is made upside-down, - do not forget to replace sealing laying.
  7. In conclusion start the engine and check components of system of production of the fulfilled gases for existence of signs of development of leaks.

M628

Cooler

Details of installation of a cooler of EGR on models 163.128 (the series 628 engine)

2 — Contact sockets of an electrical wiring
3 — Lines of a cooling path

Y27/9 — the Left positioner of EGR
Y27/10 — the Right positioner of EGR

Details of installation of a cooler of EGR on models 163.128 (the series 628 engine)

1 — EGR Cooler
4 — Bolts
5 — Connecting knot

6 — Connecting knot
And — to Pull
In — to Pull


 PERFORMANCE ORDER

  1. Details of installation of a cooler of EGR on models 163.128 (the series 628 engine) are shown on illustrations to which all references which are found in the text belong.

The cooler of EGR (1) is removed assembled positioners (Y27/9 and Y27/10).

  1. Remove assembly of the air distributor (see the Section Service of Components of an Inlet Air Path).
  2. Disunite contact sockets of an electrical wiring (2).
  3. Disconnect lines of a cooling path (3) from positioners (Y27/9 and 27/10) and a cooler (1) EGR.
  4. At first pull (arrow A) a back part of a cooler (1) up, then give assembly (arrow B) forward and disunite nipple sockets (5 and 6), - sealing rings are subject to replacement without fail.
  5. In case of need remove from assembly of a cooler (1) positioners (Y27/9 and Y27/10) (see below).
  6. Installation is made upside-down, - do not forget to replace sealing laying (see below).

Positioners

Details of installation of positioners of EGR on models 163.128 (the series 628 engine)


 PERFORMANCE ORDER

  1. Details of installation of positioners of EGR are shown on сопр. an illustration to which all references which are found in the text belong.
  2. Remove a cooler (see above)
  3. Turn out fixing bolts (1) and remove positioners (Y27/9 and Y27/10) from assembly of a cooler of EGR.
  4. Installation is made upside-down, - do not forget to replace sealing laying (2).